Nintendo NES RF-module removal

I was looking for a broken NES so I could use its case for a project I’ve been thinking about. I found one on eBay at a reasonable price, so I bought it.

Once I got the unit, I found out that it had the infamous “flashing red LED” problem, which was easily remedied by disabling the lockout chip. After that I couldn’t just gut the poor thing, as the unit might have been fine, so I inserted a game, connected a TV with an RF cable, and turned the NES on.

The video had noise in the form of vertical lines, and there was no audio at all. “Oh well, might as well gut this one, then.” Unless…

Connecting the unit with the AV cables gave better results: The video still had the lines, but now there was audio. I googled for a bit, and found out that this may be caused by a faulty RF-modulator unit. The solution would be removing the unit, and adding new AV connectors as well as a new video amp.


So, I decided to give it a try. This instructable had instructions on making the amplifier for the video signal, and this forum discussion listed the functions for the pins that connect to the RF-modulator:

After removing the RF box, you will see 5 holes with contacts. Hold the board so it is in the upper-left corner and they are as follows (from left to right): Power, Reset, +5v (if you connect it here, it will go directly into the system, this is usually where the output from the Power switch goes), audio out, and weak video output.

I would also have to provide +5V DC to power the unit, as the original regulator and rectifier are parts of the RF-modulator.

The first order of business was removing the RF-modulator unit. I managed to de-solder the whole thing in more or less one piece, but thinking back, I probably should have just cut it off in pieces. In this picture I’ve already added header connectors for the five contacts that were connected to the RF-modulator, as well as two more for GND (top left of the image).

IMG_0864

In the end I only needed to use three of the pins: The audio and video signals and “+5V” as described on the forum.

I then replaced two of the wires coming from the NES power/reset button unit (red and brown) and added a pin header connector in the end:

IMG_0863

Next, I needed new AV-connectors, a new power connector, and the replacement video amplifier. I mounted all of this on a piece of strip board. The board could’ve been much smaller, but I wanted to be able to use the original mounting holes on the NES.

IMG_0865

The blue plastic piece is a box for hobby knife blades that I happened to have laying around. It was the perfect size for mounting the power connector on the board. I used a 4mm connector instead of the original 5.5mm one to make sure no-one (i.e. me) accidentally plugs in an original NES PSU. Connecting 9V AC to the parts of the NES that expect 5V DC wouldn’t be pretty. I got a 5V wall wart to use as the PSU, and swapped a 4mm connector on that one as well.

The wiring is simple:
– The video amp as shown in the Instructable
– The NES audio pin directly to the audio connector
– The (orange in the picture) wire from the NES +5V pin connects to the brown wire coming from the NES power button (i.e. this doesn’t really need to go through the strip board, but it made for neater wiring)
– The red wire from the NES power button connects to the new power connector’s +5V
– The black wires connect NES GND to strip board GND and power supply GND.

Here’s the strip board in the case:

IMG_0866

And connected to the NES main board (with the connector made of 7 header pins, not visible):

IMG_0868

Looks pretty neat when all closed up:

IMG_0869

After this bypass/transplant operation the patient is feeling fine. The only problem is some hum in the audio, so I might try using a shielded cable for the audio signal in case that’s the problem. Other than that, I’ve now got a perfectly fine NES.

Next step: Find a broken NES that I can gut with a clear conscience for that other project I was planning on doing…

[EDIT 2016-11-13, in response to Victor’s comment:]

Ok, so the red and brown wires are in fact the main power switch wires. They originally connected to the main board (with the white, yellow and orange), and were routed to the RF-modulator.

I _guess_ the power switch would no longer work, since the part it was connected to was gone. Also, it makes sense to me to have the power switch as close to the power connector as possible.

I’ve added a couple of pictures. I hope this helps!

img_0336

img_0335

12 comments

  1. Go ahead, although it’s been ages and I probably won’t remember anything that’s not written down here…

  2. I had no idea about the “lock out chip” – I’m going to have to try that. Otherwise this is great information about replacing the RF Box. Thanks

  3. This is awesome! I’ve been looking for a way to get rid of the RF box to fit my console in a different case. Everything else are those portable rigs.

  4. Great post!

    Here are my thoughts….

    “In the end I only needed to use three of the pins: The audio and video signals and ā€œ+5Vā€ as described on the forum.”

    “I then replaced two of the wires coming from the NES power/reset button unit (red and brown) and added a pin header connector in the end”

    – I don’t see the point “replacing” the two of the wires coming from the NES power/reset button unit and not utilizing the original pins. So you’ve added the heads not to you them? Instead you decided for cutting the original wires? Where is the gain?

    What is also not clear is how you wired up the reset(brown) button. Can you give more details?

    I am sure this post will still be useful to a lot of people.

    Thanks for taking the time to create!

    Victor

  5. It’s been a while so I can’t really remember the details. I’ll have to open the unit and have a look. I’ll get back to you, hopefully in a few days.

  6. Ok, so the red and brown wires are in fact the main power switch wires. They originally connected to the main board (with the white, yellow and orange), and were routed to the RF-modulator.

    I _guess_ the power switch would no longer work, since the part it was connected to was gone. Also, it makes sense to me to have the power switch as close to the power connector as possible.

    I’ve added a couple of pictures. I hope this helps!

      1. That’s actually a pretty decent guess. I might try testing powering the unit with a battery to see if that’s the case. Thanks for the tip!

Leave a Reply to Brandon Cancel reply

Your email address will not be published. Required fields are marked *